LSN2-T/30-D12-C【PDF 6/16 页】CONV DC/DC 150W 30A 0.8-5V SIP

您好，
买卖IC网欢迎您。
请登录
免费注册

2页 3页 4页 5页 [6页]7页 8页 9页 10页

LSN2-T/30-D12 Series

DOSA-SIP, 30A POL DC/DC Converters

The speci?cation de?nes the interval between the time at which the converter

is turned on and the fully loaded output voltage enters and remains within its

speci?ed accuracy band. See Typical Performance Curves.

Remote Sense

LSN2-T/30-D12 Series offer an output sense function. The sense function

enables point-of-use regulation for overcoming moderate IR drops in conduc-

tors and/or cabling. Since these are non-isolated devices whose inputs and

outputs usually share the same ground plane, sense is provided only for the

+Output.

The remote sense line is part of the feedback control loop regulating the

DC/DC converter’s output. The sense line carries very little current and conse-

quently requires a minimal cross-sectional-area conductor. As such, it is not a

low-impedance point and must be treated with care in layout and cabling. Sense

Figure 3. Measuring Output Ripple/Noise (PARD)

The most effective combination of external I/O capacitors will be a function

of your line voltage and source impedance, as well as your particular load and

layout conditions.

Input Fusing

Most applications and or safety agencies require the installation of fuses at the

inputs of power conversion components. The LSN2-T/30-D12 Series are not

internally fused. Therefore, if input fusing is mandatory, either a normal-blow

or a slow-blow fuse with a value no greater than twice the maximum input cur-

rent calculated at low line with the converter’s minimum ef?ciency should be

installed within the ungrounded input path to the converter.

Safety Considerations

LSN2-T/30-D12 SIPs are non-isolated DC/DC converters. In general, all DC/DC’s

must be installed, including considerations for I/O voltages and spacing/separa-

tion requirements, in compliance with relevant safety-agency speci?cations

(usually UL/IEC/EN60950-1).

In particular, for a non-isolated converter’s output voltage to meet SELV

(safety extra low voltage) requirements, its input must be SELV compliant. If the

output needs to be ELV (extra low voltage), the input must be ELV.

Input Overvoltage and Reverse-Polarity Protection

LSN2-T/30-D12 SIP Series DC/DCs do not incorporate either input overvoltage

or input reverse-polarity protection. Input voltages in excess of the speci?ed

absolute maximum ratings and input polarity reversals of longer than “instan-

taneous” duration can cause permanent damage to these devices.

Start-Up Time

The V IN to V OUT Start-Up Time is the interval between the time at which a ramp-

ing input voltage crosses the lower limit of the speci?ed input voltage range

and the fully loaded output voltage enters and remains within its speci?ed

accuracy band. Actual measured times will vary with input source impedance,

external input capacitance, and the slew rate and ?nal value of the input voltage

as it appears to the converter.

lines should be run adjacent to signals (preferably ground), and in cable and/or

discrete-wiring applications, twisted-pair or similar techniques should be used.

To prevent high frequency voltage differences between V OUT and Sense, we

recommend installation of a 1000pF capacitor close to the converter.

The sense function is capable of compensating for voltage drops between

the +Output and +Sense pins that do not exceed 10% of V OUT .

[V OUT (+) – Common] – [Sense(+) – Common] ≤ 10%V OUT

Power derating (output current limiting) is based upon maximum output cur-

rent and voltage at the converter’s output pins. Use of trim and sense functions

can cause the output voltage to increase, thereby increasing output power

beyond the LSN2-T/30-D12’s speci?ed rating. Therefore:

(V OUT at pins) x (I OUT ) ≤ rated output power

The internal 10.5 Ω resistor between +Sense and +Output (see Figure 1)

serves to protect the sense function by limiting the output current ?owing

through the sense line if the main output is disconnected. It also prevents

output voltage runaway if the sense connection is disconnected.

Note: If the sense function is not used for remote regulation, +Sense

must be tied to +Output at the DC/DC converter pins.

Remote On/Off Control

Normally this input is controlled by the user’s external transistor or relay or is

permanently grounded. With simple external circuits, it may also be selected

by logic outputs. The On/Off control takes effect only when appropriate input

power has been applied and stabilized (approximately 7msec).

For negative polarity, the default operation leaves this pin grounded or LOW.

The output will then always be on (enabled) whenever appropriate input power

is applied.

Dynamic control of the On/Off must be capable of sinking or sourcing the

control current (approximately 1mA max.) and not overdrive the input greater

than the +V IN power input. Always wait for the input power to stabilize before

activating the On/Off control.

The On/Off to V OUT Start-Up Time assumes the converter is turned off via the

On/Off Control with the nominal input voltage already applied to the converter.

www.murata-ps.com/support

MDC_LSN2-T/30-D12 Series.C01 Δ Page 6 of 16

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

LSS-T/10-W12-C CONV DC/DC 60W 10A .6-6V SIP

LTM4600HVIV#PBF IC DC/DC UMODULE 10A 104-LGA

LTM4600IV#PBF IC DC/DC UMODULE 10A 104-LGA

LTM4601AHVEV#PBF IC DC/DC UMODULE 12A 133-LGA

LTM4601AIY#PBF IC DC/DC UMODULE 12A 133-BGA

LTM4602IV#PBF IC DC/DC UMODULE 6A 104-LGA

LTM4603HVEV#PBF IC DC/DC UMODULE 6A 118-LGA

LTM4603IV#PBF IC DC/DC UMODULE 6A 118-LGA

相关代理商/技术参数

LSN2-T/30-D12G-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W Power Good Out RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/30-D12N-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W Neg polarity RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/30-D12NG-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W PowerGood NegPl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-C 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

LSN2-T/6-D12 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

LSN2-T/6-D12-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-D12G-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-D12N-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: